Abstract
Lithium batteries are receiving considerable attention as storage devices in the renewable energy and sustainable road transport fields. However, low-cost, long-life lithium batteries with higher energy densities are required to facilitate practical application. Here we report a lithium-ion battery that can be cycled at rates as high as 10 C has a life exceeding 500 cycles and an operating temperature range extending from −20 to 55 °C. The estimated energy density is 260 W h kg−1, which is considerably higher than densities delivered by the presently available Li-ion batteries.
Similar content being viewed by others
Introduction
The replacement of internal combustion engine cars with electric vehicles, such as hybrid vehicles, plug-in hybrid vehicles and, ultimately, full electric vehicles, will require the development of advanced rechargeable batteries. Li-ion batteries have high intrinsic energy density values and are promising candidates1,2, but current Li-ion battery technologies are not yet able to meet the requirements of efficiently storing alternative energy sources and/or powering hybrid or electric vehicles. Reduction in cost, enhancement in safety, and improvement in energy density are the main properties that have to be implemented. To achieve these important goals, a renewal in the present lithium battery chemistry, aimed at the replacement of costly and unsafe lithium cobalt oxide and of thermodynamically unstable graphite with alternative, morphologically upgraded, reliable cathode and anode, respectively, is mandatory3,4,5.
Here we report a high-performance lithium-ion battery that exploits a unique electrode combination. The battery utilizes existing concepts but offers performances that, to our knowledge, have never been met by other systems. We show that the battery can be cycled at rates as high as 10 C rate with minor decays in capacity, that it has an unusually long life: exceeding 500 cycles at 1 C rate; and may operate over a wide temperature range: from −20 °C to 55 °C, with no substantial losses in cycling stability and capacity delivery.
Results
Battery structure
The battery developed in this work is based on the combination of a Li4Ti5O12 (LTO) negative electrode with a Li[Ni0.45Co0.1Mn1.45]O4 (LNMO)-positive electrode. LTO is a well-known material benefitting by a series of important properties when exploited as electrode in lithium cells, including: minor or no volume changes during cycling and voltage excursion comprised within the electrochemical windows of most common electrolytes6,7,8,9. Accordingly, LTO may be repeatedly cycled without inducing any electrolyte decomposition10,11. However, these favourable aspects may be contrasted by relatively low rates, unless LTO is prepared with adequate, specially designed morphology.
Advanced LTO electrode
By a synthesis procedure originally conceived in our laboratory12, we have developed a C-coated microscale LTO involving composites between nano-sized LTO particles and carbon. This particular morphology is clearly shown by the scanning electron microscopy and transmission electron microscopy (TEM) images reported in Figure 1. Figure 1a shows that that the aggregates of nano-sized LTO particles and Figure 1b that these particles are intimately interconnected by carbon bridges. The X-ray diffraction, also included in the same Figure 1, reveals the occurrence of all the peaks associated with LTO, so demonstrating the purity of the material and confirming the nano-size of its primary particles as evidenced by the TEM analysis.
The carbon bridges act as electron pathways that electrically interconnect the LTO particles, ultimately providing the electrode with a very high conductivity that, combined with the reduction of the lithium diffusion length within the particles (10–20 nm in diameter, see TEM image of Fig. 1), is expected to provide the LTO electrode with fast kinetics. This is indeed confirmed by Figure 2 that shows the voltage profile of the first charge (lithium acceptance)–discharge (lithium removal) cycle (a) and incremental charge (dQ) versus potential (b) curve of the potentiodynamic cycling with galvanostatic acceleration (PCGA) analysis of two consecutive cycles of the C-coated LTO electrode in a lithium cell. The PCGA analysis is a quasi-equilibrium technique that can provide very useful detailed information of the characteristics of electrochemical processes13. We see from Figure 2b that the electrode cycles along the expected plateau at about 1.5 V versus Li/Li+, with a capacity delivery approaching the theoretical value of 175 mA h g−1. Most impressive is the absence of hysteresis between charge and discharge profiles, an effect that indicates a very high coulombic efficiency and very fast kinetics. Figure 2b, reporting the incremental charge dQ versus potential extended for two consecutive cycles, evidences that the traces overlap and there is almost no separation between the anodic and the cathodic peaks. All the above evidences provide convincing proofs of the excellent cycle life and rate capability of our C-coated LTO electrode.
This conclusion is further supported by Figure 3 that summarizes the response of the electrode in a lithium cell. The data demonstrate that the electrode can be effectively cycled at current rates as high as 20 C rate while still maintaining a capacity delivery of 156 mA h g−1, that is 89% of the maximum, theoretical value (Fig. 3a) and that the delivered capacity of 162 mAh g−1 at 3 C rate can be maintained without any evidence of decay for over 100 cycles (Fig. 3c). We are not aware of other micro-sized LTO electrodes capable of meeting these performances. Finally, it has to be noticed that a key parameter for an electrode to be used in practical batteries is the value of the tap density that in turn reflects the volumetric energy density of the battery. The common approach to achieve high volumetric capacity is to prepare the LTO electrode in micro-size, spherical, and dense particles. However, while having a high tap density, these micro-size LTO electrodes usually suffer from poor capacity and rate capability, because of the limitation induced by the long Li+ diffusion path throughout the particles14,15. On the contrary, our LTO electrode, in virtue of its unique nanoporous morphology exploiting a uniform, highly conductive carbon-coating layer, marks superiority over conventional materials, by offering a relatively high tap density, that is, 1.31 g cm−3 combined with excellent electrochemical performance.
The positive electrode material
The cathode selected for combination with LTO is the LNMO spinel. The preparation of this material is also based on a synthesis originally developed in our laboratory. Its basic characteristics in a lithium cell have been reported in a previous work16. For a matter of consistency, that is, to check whether the response of the LNMO electrode matches that of LTO, we only report here the voltage profiles and the differential capacity (dQ/dV) curves in a lithium cell. Figure 4 shows that the LNMO electrode operates with two plateaus, corresponding to the two redox processes of nickel, that is, Ni2+/Ni3+ and Ni3+/Ni4+, at 4.6 V and 4.7 V, respectively. The two steps are clearly evidenced in the corresponding dQ/dV response: the overlap of the peaks and their very small separation suggest that also this electrode operates with a high efficiency, a long cycling life and fast kinetics. The tap density of the LNMO electrode is 2.20 g cm−3, a value that compares well with that of LTO.
Discussion
The Li[Ni0.45Co0.1Mn1.45]O4 electrode material discussed here differs from the more conventional Li[Ni1/2Mn3/2]O4 (refs 17,18) for the unique role of the Co substitution for both Ni and Mn, thus improving structural stability and electronic conductivity, finally resulting in an electrode having high cycling stability and rate capability.
As expected from their respective voltages, the combination of LTO with LNMO gives rise to a battery operating in the 3 V range. Figure 5a shows the voltage profiles of the charge (lithium transfer from LNMO to LTO)–discharge (back transfer of lithium from LTO to LNMO) cycles of the battery. To be noticed that both the very flat voltage profile centered on 3 V and the very small hysteresis between charge and discharge behavior during a long cycling effect are concrete evidences of high reversibility and fast kinetics. The battery, in fact, may be cycled at 1 C rate with 128 mA h g−1 capacity delivery, that is, at a value closed to the theoretical one (the battery is cathode limited) (Fig. 5a) and for a life extending 500 cycles with only 14.6% capacity loss, (Fig. 5c). Also, the battery has excellent rate performance and can be cycled up to 10 C with the only 16.5% capacity decay (Fig. 5c).
Finally, a crucial parameter for a battery addressed to the storage of renewable energy sources, as well as to the powering of electric car engines, is the capability to sustain efficient operations over a wide temperature range. Figure 6a shows that the LTO/LNMO battery developed in this work fulfills this requirement as it cycles with excellent voltage and capacity retention over a temperature excursion spanning from −20 to +55 °C. In addition, even at these extreme temperature limits, the battery cycles with a very stable capacity delivery (Fig. 6b).
We are aware that the concept of combining LTO with different positive electrode materials to form stable and long-life batteries is not new. It was originally proposed in 2003 by Ohzuku and co-workers19 and in 2004 by us20, and it is presently exploited in various laboratories21,22. With this work, we have marked a step forward in the field as the LTO/LNMO battery here reported shows rate, life and energy performance, to our knowledge, never reached before. From the data of Figure 5, that demonstrate a stable capacity delivery of 124 mA h g−1, a maximum value of 372 W h kg−1 of energy density is obtained. By using the accepted 40% penalty factor to account for the weight of the electrolyte and of the ancillary components (case, current collectors and so on), a practical energy density of 225 of W h kg−1 may be anticipated, that is, a value considerably higher than that delivered by the presently available Li-ion batteries. In addition, our LTO/LNMO battery, in virtue of the high tap density of the electrodes, is also expected to have a high volumetric energy density, estimated of the order of 540 W h l−1. Last, but certainly not least, the unique morphology of the electrode consents the battery to operate at high rates over a temperature range extending from −20 to 55 °C. We believe that all the above stressed features make the LTO/LNMO battery here reported a unique electrochemical device that outclasses other competitor systems for operation in the energy and transportation fields.
Methods
Synthesis of C-LTO
The microscale, C-coated Li4Ti5O12 anode material was prepared by mixing highly mesoporous anatase TiO2 with a stoichiometric amount of Li2CO3 and pitch as the carbon-coating source. The carbon content in C-Li4Ti5O12 was 5.2 wt%.
Details of the synthesis route are reported in previous papers12,23,24. The spherical Li[Ni0.45Co0.1Mn1.45]O4 cathode was synthesized by co-precipitation of NiSO4·6H2O, CoSO4·7H2O and MnSO4·5H2O. Details of the preparation procedures are reported elsewhere16,25.
Morphology and structure studies
The morphology of the synthesized materials was analysed by field-emission scanning electron microscopy (JSM-6400, JEOL) and high-resolution transmission electron microscopy (JEM-2010, JEOL). The structure was determined by Powder X-ray diffraction, carried out using a Rigaku Rint-2000 with Cu Ka radiation. The diffraction data were obtained at 2θ=10° to 80°, with a step size of 0.03°.
Preparation of electrodes and cells
The electrodes were prepared by mixing powders of the active materials, that is, Li[Ni0.45Co0.1Mn1.45]O4 and C-coated Li4Ti5O12, respectively, with carbon black and polyvinylidene fluoride (80:10:10) in N-methylpyrrolidinon. The obtained slurry was coated onto Al or Cu foils, respectively, and roll-pressed. The electrodes were then dried overnight at 120 °C in vacuum, before use. The initial electrochemical tests were done with a 2032 coin-type cell using Li metal as the anode. The capacities of the electrodes were referred to the electrode material as a whole, including the minor carbon coating content. The size of the Li[Ni0.45Co0.1Mn1.45]O4-positive electrode is 3 cm×5 cm and that of the negative C-Li4Ti5O12, is 3.1 cm×5.1 cm. The weight of the two electrodes were 104.4 mg and 112.2 mg, respectively, so as to lead to a N/P (negative/positive) electrode ratio of 1.36 in the laminated-type cell.
Preparation of the battery
The LTO/LNMO battery was assembled by a laminated-type full cell, wrapped with an Al pouch. The battery was cathode limited. The electrolyte solution was 1.2 M LiPF6 in ethylene carbonate-dimethyl carbonate (3:7 in volume).
Battery tests
The batteries were charged and discharged between 2.0–3.4 V voltage limits, at various C-rates (1 C rate corresponding to 135 mA h g−1) and at different temperatures. The PCGA test was performed using a VMP biologic-science instrument with a stepwise potential scans of 5 mV and minimum current limit of 10 μA within a 1.0–3.0 V versus Li potential limits. The test was run in a three-electrode cell where the working electrode sample was combined with a lithium foil used as reference and counter electrode.
Additional information
How to cite this article: Jung, H.-G. et al. A high-rate long-life Li4Ti5O12/Li[Ni0.45Co0.1Mn1.45]O4 lithium-ion battery. Nat. Commun. 2:516 doi: 10.1038/ncomms1527 (2011).
References
Scrosati, B. & Garche, J. Lithium batteries: status, prospects and future. J. Power Sources 195, 2419–2430 (2010).
Bradley, T. H. & Frank, A. A. Design, demonstrations and sustainability impact assessments for plug-in hybrid electric vehicles. Renew. Sust. Energ. Rev. 13, 115–128 (2009).
Aricò, A. S., Bruce, P. G., Scrosati, B., Tarascon, J.- M. & van Schalkwick, W. Nanostructured materials for advanced energy conversion and storage devices. Nature Mater. 4, 366–377 (2005).
Tarascon, J.- M. & Armand, M. Issues and challenges facing rechargeable lithium batteries. Nature 414, 359–367 (2001).
Scrosati, B., Hassoun, J. & Sun, Y.- K. Lithium-ion batteries. A look into the future. Energy Environ. Sci. 4, 3287–3295 (2011).
Ohzuku, T., Ueda, A. & Yamamoto, N. Zero-strain insertion material of Li[Li1/3Ti5/3]O4 for rechargeable lithium cells. J. Electrochem. Soc. 142, 1431–1435 (1995).
Colbow, K. M., Dahn, J. R. & Haering, R. R. Structure and electrochemistry of the spinel oxides LiTi2O4 and Li4/3Ti5/3O4 . J. Power Sources 26, 397–402 (1989).
Jiang, C., Ichihara, M., Honma, I. & Zhou, H. Effect of particle dispersion on high rate performance of nano-sized Li4Ti5O12 anode. Electrochim. Acta 52, 6470–6475 (2007).
Cheng, L. et al. General synthesis of carbon-coated nanostructured Li4Ti5O12 as a high rate electrode material for Li-ion intercalation. J. Mater. Chem. 20, 595–602 (2010).
Ronci, F. et al. High-resolution In-Situ structural measurements of the Li4/3Ti5/3O4 “Zero-Strain” insertion material. J. Phys. Chem. B 106, 3082–3086 (2002).
Belharouak, I., Sun, Y.- K., Lu, W. & Amine, K. On the safety of the Li4Ti5O12/LiMn2O4 lithium-ion battery system. J. Electrochem. Soc. 154, A1083–A1087 (2007).
Jung, H.- G. et al. Microscale spherical carbon-coated Li4Ti5O12 as ultra high power anode material for lithium batteries. Energy Environ. Sci. 4, 1345–1351 (2011).
Thompson, A. H. Electrochemical potential spectroscopy: a new electrochemical measurement. J. Electrochem. Soc. 126, 608–616 (1979).
Nakahara, K., Nakajima, R., Matsushima, T. & Majima, H. Preparation of particulate Li4Ti5O12 having excellent characteristics as an electrode active material for power storage cells. J. Power Sources 117, 131–136 (2003).
Gao, J., Ying, J., Jiang, C. & Wan, C. High-density spherical Li4Ti5O12/C anode material with good rate capability for lithium ion batteries. J. Power Sources 166, 255–259 (2007).
Hassoun, J., Lee, K.- S., Sun, Y.- K. & Scrosati, B. An advanced lithium ion battery based on high performance electrode materials. J. Am. Chem. Soc. 133, 3139–3143 (2011).
Ariyoshi, K., Iwakoshi, Y., Nakayama, N. & Ohzuku, T. Topotactic two-phase reactions of Li[Ni1/2Mn3/2]O4(P4332) in nonaqueous lithium cells. J. Electrochem. Soc. 151, A296–A303 (2004).
Ariyoshi, K., Maeda, Y., Kawai, T. & Ohzuku, T. Effect of primary particle size upon polarization and cycling stability of 5-V lithium insertion material of Li[Ni1/2Mn3/2]O4 . J. Electrochem. Soc. 158, A281–A284 (2011).
Ariyoshi, K., Yamamoto, S. & Ohzuku, T. Three-volt lithium-ion battery with Li[Ni1/2Mn3/2]O4 and the zero-strain insertion material of Li[Li1/3Ti5/3]O4 . J. Power Sources 119–121, 959–963 (2003).
Reale, P., Panero, S., Scrosati, B., Garche, J., Wohlfahrt-Mehrens, A. & Wachtler, M. A safe, low-cost, and sustainable lithium-ion polymer battery. J. Electrochem. Soc. 151, A2138–A2142 (2004).
Guerfi, A. et al. Improved electrolytes for Li-ion batteries: mixtures of ionic liquid and organic electrolyte with enhanced safety and electrochemical performance. J. Power Sources 195, 845–852 (2010).
Ariyoshi, K. et al. Three-volt lithium-ion battery consisting of Li[Ni1/2Mn3/2]O4 and Li[Li1/3Ti5/3]O4: improvement of positive-electrode material for long-life medium-power applications. Electrochemistry 76, 46–54 (2008).
Jung, H.- G. et al. Mesoporous TiO2 nano networks: anode for high power lithium battery applications. Electrochem. Commun. 11, 756–759 (2009).
Jung, H.- G., Yoon, C. S., Prakash, J. & Sun, Y.- K. Mesoporous anatase TiO2 with high surface area and controllable pore size by F−-ion doping: applications for high-power Li-ion battery anode. J. Phys. Chem. C 113, 21258–21263 (2009).
Oh, S.- W., Myung, S.- T., Kang, H.- B. & Sun, Y.- K. Effects of Co doping on Li[Ni0.5CoxMn1.5−x]O4 spinel materials for 5V lithium secondary batteries via Co-precipitation. J. Power Sources 189, 752–756 (2009).
Acknowledgements
This work was carried out and supported in part by the WCU (World Class University) program through the National Research Foundation of Korea funded by the Ministry of by Education, Science and Technology (R31-2008-000-10092) and by the Human Resources Development of the Korea Institute of Energy Technology Evaluation and Planning (KETEP) grant funded by the Korea government Ministry of Knowledge Economy (No. 20104010100560) and, in part, by the Italian Institute of Technology in the framework of the SEED Project 'REALIST' (Rechargeable, advanced, nano structured lithium batteries with high energy storage).
Author information
Authors and Affiliations
Contributions
B.S. conceived the idea of combining LTO with LNMO for the development of the battery. Y.-K.S. designed the synthesis for obtaining high-performance LTO and LNMO electrode. J.H. directed the experimental work. H.-G.J. fabricated the cell. M.W.J. conducted the measurements. B.S., Y.-K.S. and J.H. wrote the manuscript.
Corresponding authors
Ethics declarations
Competing interests
The authors declare no competing financial interests.
Rights and permissions
About this article
Cite this article
Jung, HG., Jang, M., Hassoun, J. et al. A high-rate long-life Li4Ti5O12/Li[Ni0.45Co0.1Mn1.45]O4 lithium-ion battery. Nat Commun 2, 516 (2011). https://doi.org/10.1038/ncomms1527
Received:
Accepted:
Published:
DOI: https://doi.org/10.1038/ncomms1527
This article is cited by
-
Few-layer bismuth selenide cathode for low-temperature quasi-solid-state aqueous zinc metal batteries
Nature Communications (2022)
-
Metal–Organic Frameworks and Their Derivatives as Cathodes for Lithium-Ion Battery Applications: A Review
Electrochemical Energy Reviews (2022)
-
Facile controlled synthesis of hierarchically structured mesoporous Li4Ti5O12/C/rGO composites as high-performance anode of lithium-ion batteries
Frontiers in Energy (2022)
-
Subduction zone fluids and arc magmas conducted by lithospheric deformed regions beneath the central Andes
Scientific Reports (2021)
-
A Bifunctional-Modulated Conformal Li/Mn-Rich Layered Cathode for Fast-Charging, High Volumetric Density and Durable Li-Ion Full Cells
Nano-Micro Letters (2021)
Comments
By submitting a comment you agree to abide by our Terms and Community Guidelines. If you find something abusive or that does not comply with our terms or guidelines please flag it as inappropriate.