Abstract
Controlling wettability by varying surface chemistry and roughness or by applying external stimuli is of interest for a wide range of applications including microfluidics, drag reduction, self-cleaning, water harvesting, anti-corrosion, anti-fogging, anti-icing and thermal management. It has been well known that droplets on textured hydrophilic, that is superhydrophilic, surfaces form thin films with near-zero contact angles. Here we report an unexpected behaviour where non-wetting droplets are formed by slightly heating superhydrophilic microstructured surfaces beyond the saturation temperature (>5 °C). Although such behaviour is generally not expected on superhydrophilic surfaces, an evaporation-induced pressure in the structured region prevents wetting. In particular, the increased thermal conductivity and decreased vapour permeability of the structured region allows this behaviour to be observed at such low temperatures. This phenomenon is distinct from the widely researched Leidenfrost and offers an expanded parametric space for fabricating surfaces with desired temperature-dependent wettability.
Similar content being viewed by others
Introduction
When a water droplet is placed on a rough hydrophilic surface at room temperature, it spontaneously spreads with a near-zero contact angle (Fig. 1a). This behaviour is explained by the classical Wenzel equation1,2,3,4 where roughness enhances the wettability of a smooth hydrophilic surface because of the reduction in the surface energy of the system. Typically, as the temperature of such surfaces increase, the wettability is expected to improve because of a decrease in the surface tension of the liquid. However, a microstructured surface heated to a critical temperature beyond the saturation temperature can sustain non-wetting droplets with contact angles as high as ≈160° (Fig. 1b). Detailed visualization of the solid–liquid contact line revealed that these non-wetting droplets touch the top of the pillars (inset, Fig. 1b).
Although this phenomenon has not been previously reported, the effect of heating and temperature on the wetting morphology of droplets on micro-/nanostructured surfaces has been studied experimentally5,6 where droplet mobility has been shown to increase with temperature. At higher temperatures, the droplets exhibit the classical Leidenfrost phenomenon7,8, where solid–liquid contact is absent because of the presence of a thin vapour layer (thickness ≈10–100 μm)9 that completely separates the droplet from the heated surface10,11,12,13. The reported values of the Leidenfrost temperature on a flat silicon surface ranges from 200 to 390 °C9,14,15,16,17,18. Although the majority of the studies on textured surfaces report a relative increase in the Leidenfrost temperature10,14,18,19,20,21,22, a few recent studies reported a significant decrease in the Leidenfrost temperature on microstructured hydrophobic surfaces23,24,25,26. For example, del Cerro et al.23 observed suspended droplets on heated surfaces composed of hydrophobic micropillars and microholes at temperatures 70% lower than the Leidenfrost point on a smooth surface. Meanwhile, Vakarelski et al.24 reported that the Leidenfrost-like phenomenon of film boiling could be observed at extremely low superheats on superhydrophobic textured surfaces and was key to avoiding vigorous boiling because of the explosive transition from the Leidenfrost to the nucleate boiling regime. This non-wetting behaviour was attributed to the inherent water repellency of superhydrophobic surfaces, and was presumed to be absent on superhydrophilic surfaces24,27.
In this work, however, we show that non-wetting droplets can reside even on superhydrophilic surfaces at superheats (Twall−Tsat) of ≈5–50 °C, far below the Leidenfrost point, where Twall is the temperature of the substrate at the solid–liquid interface and Tsat is the saturation temperature of the liquid. A mechanistic understanding of this wetting process was obtained by developing a one-dimensional force balance model, which was validated with experimental data acquired on various micropillar geometries. The low superheat that was required to obtain the non-wetting droplets on superhydrophilic surfaces is attributed to the high-pressure region created because of the presence of the micropillars that significantly increases the thermal conductivity and decreases the vapour permeability of the porous media beneath the droplet (between the droplet base and the substrate). Physical insights gained from our systematic experiments and modelling demonstrate that the wetting behaviour of droplets at room temperature does not necessarily hold at superheated conditions and, further, explain how textured hydrophilic surfaces can exhibit drastically different and yet potentially very useful wetting characteristics at superheated conditions. The observed behaviour is not only a function of the structure geometry and surface energy but also the size of the droplet and the thermal properties of the substrate material. These results have significant implications for processes such as spray cooling of hot metals during metallurgical processes, cooling of nuclear reactors during emergency shutdown, heat exchangers and cooling of overheated components in high-power-density thermal applications12 where solid–liquid contact is desired for improved heat transfer performance. The non-wetting mechanism also suggests a route to sustained surface-energy-independent drag reducing surfaces at superheats significantly lower than the Leidenfrost point25.
Results
Experiments
Well-defined silicon micropillar arrays arranged in a square pattern with varying diameter (D), height (H) and pitch (L; see Table 1) were fabricated using standard contact photolithography and deep reactive ion etching. The scanning electron microscope images of the six test samples used in this investigation are shown in the Supplementary Fig. S1. The typical intrinsic contact angle (θY) of organically contaminated SiO2 surfaces is ≈38–42° (refs 28, 29, 30), which was also confirmed in our experiments. A platinum resistive heater and four sensors for measuring temperature were patterned on the backside of the sample using e-beam evaporation and standard lift-off processes. The details of the microfabrication, sample cleaning procedure, experimental set-up and methodology are discussed in the Methods section.
We performed droplet wetting experiments on superheated hydrophilic microstructured surfaces at atmospheric pressure to investigate the effect of substrate temperature, surface geometry (D, H and L) and droplet size on wetting morphology. To determine the critical deposition temperature beyond which droplets become non-wetting, droplets were gently deposited onto the microstructured surface at a prescribed temperature. Figure 1c summarizes the probability, P, of obtaining non-wetting water droplets (out of 10 attempts) on the superhydrophilic surface as a function of the back side substrate temperature. All droplets wetted the surface (P=0) when the substrate temperature was <150 °C, whereas none of them wetted (P=1) when the temperature was >165 °C.
To investigate the effect of droplet size on the wetting state, experiments were also carried out where the substrate temperature was lowered and allowed to stabilize after depositing a non-wetting droplet. Details of a typical experiment are shown in Fig. 2. Figure 2ai corresponds to a newly deposited non-wetting water droplet on a superhydrophilic surface at a temperature of 170 °C (Fig. 2b). Once deposited, the droplet remained non-wetting (Fig. 2aii) even after the temperature was subsequently reduced and stabilized at 112 °C (Fig. 2b). It is noteworthy that this surface temperature (112 °C) was significantly lower than the critical transition temperature shown in Fig. 1c. When sufficient time was given for the droplet to evaporate, however, a spontaneous wetting transition followed by vigorous nucleate boiling occurred at t=34.3 s (Fig. 2aiii) corresponding to a droplet base radius of Rbase≈0.80 mm (Fig. 2c). Because of the increased solid–liquid contact following transition, we observed a significant temperature reduction in the substrate beneath the droplet (Fig. 2b). A movie illustrating the dynamic nature of the non-wetting droplet corresponding to the data in Fig. 2 can be found in the Supplementary Movie 1.
Modelling
To explain the mechanism of non-wetting droplets on a superhydrophilic surface, we developed a one-dimensional force balance model that includes gravity and surface tension as the wetting forces and evaporation-induced pressure as the non-wetting force. We attribute the higher superheat required for initial droplet deposition (t=0 s, Fig. 2b) compared with that necessary to maintain the non-wetting droplet (t>9 s, Fig. 2b) to the additional wetting forces of water hammer31,32,33 and dynamic pressure at the start of the experiment. Consequently, the non-wetting force and hence the temperature necessary to sustain a non-wetting droplet was lower compared with that needed to initially deposit a non-wetting droplet.
The liquid–vapor interface in our experiments is concave outwards and surface tension acts in the same direction as gravity for a superhydrophilic surface (Fig. 3a,b). It is noteworthy that for a typical superhydrophobic surface, the curvature of the liquid–vapor interface is concave inwards counteracting wetting34. The local wetting force acting around each pillar, fW=πD ϒLV, shown schematically in Fig. 3b, can be used to calculate the global average wetting force, FW, acting on the droplet as
where πRbase2/L2 accounts for the number of pillars in contact with the droplet base area, and ϒLV is the interfacial liquid–vapor surface tension of water at 100 °C. The experimentally measured global apparent contact angle of the evaporating droplet on the structured surface varied between ≈130° and ≈160°. The observed change in the apparent contact angle was because of a combination of the highly dynamic nature of the evaporating droplet (Supplementary Movie 1) and the decrease in the effect of gravity with the continuous decrease in size, rendering the models (for example, Cassie) in literature for predicting contact angle of a composite droplet invalid. As a result, we decoupled our analysis from the apparent contact angle of the droplet and accordingly used the experimentally measured droplet base radius to calculate the wetting force. Gravity was neglected in this calculation because of the relatively large contribution of the surface tension force compared with the weight of the droplet. For the experimental data discussed in this paper, the surface tension force was approximately an order of magnitude larger than the weight of the droplet. The force due to the 25 μm hydrophobized gold wire that was used to hold the droplet in position to avoid lateral movement (see Fig. 1a) was even smaller justifying the use of equation (1).
The high-pressure vapour cushion beneath the droplet provides the non-wetting force. This force is fundamentally similar to the non-wetting force in a Leidenfrost phenomenon on a flat surface; however, the homogenous vapour cushion is replaced by a porous media in our case. As shown schematically in Fig. 3c, heat conducts through the substrate and then primarily through the silicon pillars to induce evaporation at the liquid–vapor interface. The detailed modelling of the overall thermal resistance from the backside of the substrate to the liquid–vapor interface is shown in the Supplementary Information. The evaporation from the droplet spherical cap is negligible when compared with that at the droplet base35. Assuming uniform evaporation from the droplet base we then related the conducted heat with the latent heat of vaporization of water to estimate the normal mean velocity ūz of the vapour leaving the liquid–vapour interface at the droplet base (see Fig. 3c) as follows:
where Tback is the backside temperature, ρvap and hfg are the density of vapour and the latent heat of vaporization of water, respectively, Ac is the area of a unit cell (Ac=L2) and Rth is the overall thermal resistance in units of K W−1 (see Supplementary Note 1). As H/Rbase<<1, the mean velocity in the z-direction ūz is small compared with the mean velocity in the radial direction ūr (that is ūz/ūr<<1) allowing us to apply the lubrication approximation. The continuity equation at any radial position r can then be written as
Substituting equation (2) into equation (3) gives a relationship between the average radial velocity and overall temperature difference (Tback−Tsat) as
Next, we solve the appropriate momentum equation for flow in porous media, which in this case can be reduced to the classical Brinkman equation36,37,
where ε is the porosity given by ε=1−πD2/L2, K is the permeability of the porous media38, μvap is the absolute viscosity of vapour and Pvap(r) is the vapour pressure at a radial position r from the droplet centerline. Equation (5) was solved by imposing the no-slip boundary conditions (u=0) at the pillar base (z=0) and pillar top (z=H) to obtain the velocity profile of the vapour beneath the droplet base, which was then integrated from the pillar base to the pillar top to obtain the mean radial velocity as follows:
where and has units of m−1. The mean radial velocity obtained from conservation of energy (equation (4)) and from conservation of momentum (equation (6)) were then equated to solve for the radial gauge pressure profile as
where Pamb is the ambient pressure (≈101.3 kPa) at the edge of the droplet. The non-wetting force, can now be obtained by integrating the gauge pressure from equation (7) over the base area of the droplet and is given by
The criteria for the wetting transition reported in Fig. 2b was then estimated by equating the two competing forces (equation (1) and equation (8)) and solving for the superheat using the thermal resistance network as follows:
where Revap and Rs are the evaporation12 and spreading thermal resistances (see Supplementary Note 1). All thermophysical properties were evaluated at 100 °C. It is noteworthy that the backside temperature Tback that was measured experimentally is dependent on the substrate thickness and was not an appropriate measure of the superheat. Referring to the thermal resistance network in Supplementary Fig. S4, the superheat (Twall−Tsat), which is independent of substrate thickness was accordingly obtained by multiplying (Tback−Tsat) by the appropriate resistance ratio (Rs+Revap)/Rth.
The first term in parenthesis on the right hand side of equation (9) comprises fluid properties, which equivalently represents an apparent heat flux term (Wm−2). The second term in parenthesis, which is dependent on the geometry of the textured surface and the thermal conductivity of the material, represents an effective thermal resistance (m2K W−1). The third non-dimensional term, which originated from the Brinkman equation accounts for the viscous losses incurred by the presence of the micropillars.
Validation
We used our model to explain the effect of droplet size and microstructure geometry on the transition superheat. Despite the simple one-dimensional force balance adopted to obtain equation (9), Fig. 4 shows reasonable agreement between the experimental data and the model prediction over the wide parametric space investigated in this study. In addition, experiments carried out on various geometries (samples S2–S6; see Table 1) confirmed that the superheat required to suspend a non-wetting droplet on textured hydrophilic surfaces decreases when D increases (Fig. 4b), and when H and L decrease (Fig. 4c,d, respectively). The shift in the transition curve was less sensitive to the contact angles for the range of intrinsic wettability investigated in this study (see Supplementary Note 2). Figure 4 also shows that the superheat at transition is inversely proportional to the square of the base radius of the droplet. This result can be explained by the force balance, where calculations show that the wetting and the non-wetting forces scale as Rbase2 (equation (1)) and Rbase4 (equation (8)), respectively. Accordingly, the superheat that is obtained by equating the two competing forces scales as . This inverse quadratic dependence of the superheat on the base radius of the evaporating droplet indicates that smaller droplets require higher superheat to remain non-wetting, which is consistent with the experiments.
Discussion
The developed model provides the following physical insight into the mechanism of the wetting transition. When compared with Leidenfrost, the high thermal conductivity of the microstructured porous media increases the effective thermal conductivity of the gap between the droplet and the substrate, leading to increased evaporation rates at lower superheat. This effect in combination with the decreased vapour permeability due to viscous losses from the side walls of the micropillars significantly increases the pressure of the vapour cushion beneath the droplet base. As a result, the non-wetting force in our experiments was significantly higher and transition was observed at superheats significantly lower than those required for the classical Leidenfrost phenomenon. Further, the vapour layer thickness based on the classical Leidenfrost model for porous media by Avedisian et al.10 was estimated to be ≈20 μm for our experimental conditions. This estimation of the gap between the droplet base and pillar top should have been apparent in the inset image in Figs 1b and 3a where the 20-μm gap between neighbouring pillars is visible. Accordingly, the non-wetting droplets in our experiments are distinct from the classical Leidenfrost phenomenon where solid–liquid contact is completely absent because of the presence of a vapour layer that separates the droplet from the heated surface.
The understanding gained from this study suggests that low solid fraction, but high aspect ratio, small-scale structures with low thermal conductivities should be used to extend the transition superheat for heat transfer applications such as spray cooling of hot metals, cooling of nuclear reactors during emergency shutdown, heat exchangers and cooling of overheated components in high-power-density thermal applications. Conversely, larger-scale feature sizes and high thermal conductivity structures are desirable in applications where contact of the heated surface should be minimized to reduce corrosion or to generate a stable vapour on nominally hydrophilic surfaces upon mild heating for hydrodynamic drag reduction, thus opening a range of potential material systems for these applications. In addition, this framework can be extended to investigate the effect of geometry and material properties for the design of superhydrophobic surfaces at elevated temperatures.
Methods
Microfabrication
Standard contact photolithography and deep reactive ion etching were used to create silicon micropillars in a square pattern on the front side. Scanning electron microscope images of the six test samples used in this study is shown in Supplementary Fig. S1. A thin-film resistive heater and temperature sensors were patterned on the backside of the test sample using e-beam evaporation (100 nm platinum on top of a 20 nm titanium adhesive layer) and acetone lift-off. An image of a typical test sample after the microfabrication process was complete is shown in Supplementary Fig. S2. The sensors were calibrated in a conventional oven using a commercial platinum resistance temperature detector with a National Institute of Standards and Technology-traceable calibration prior to experiment. The resistance versus temperature data of the sensors was linear with <1% root mean square error.
Experimental set-up
The experimental set-up is shown in Supplementary Fig. S3. A pipette (b) was used to gently dispense droplets onto the textured surface, which was mounted on a three-dimensional stage (g) and heated using a direct current power source (c). Images were captured using CMOS camera (Phantom V7.1, Vision Research; a), whereas the backside temperature was acquired using a DAQcard (USB-6251, National Instruments; e). As discussed in Fig. 2, the substrate temperature was lowered and allowed to stabilize after depositing a non-wetting droplet on the superhydrophilic surface. The initial high temperature, which was necessary to overcome transient effects such as water hammer, was obtained by directly heating the sample through circuit 3-4-5-6-7 (solid line), whereas the lower steady-state temperature was established by actively controlling the heating power using a three-way switch (d) and a solid-state relay (f) through circuit 3-4-8-9-10-6-7 (broken line), which opens and closes at junction 9-10 based on the temperature feedback from the sensors. The turning on and off of the circuit at junction 9-10 was used to establish the lower steady-state temperature (>9 s; Fig. 2b).
Experiment methodology
A standard sample cleaning procedure was developed before experiments, where each sample was cleaned with acetone, methanol, isopropanol and deionized water, dried with nitrogen gas and oxygen plasma treated (Harrick Plasma) for 30 min. Reagent grade water (Sigma-Aldrich, CAS: 7732-18-5) was used as the working fluid. The sample was then allowed to relax in the laboratory environment such that it recovered the intrinsic static contact angle of ≈38–42° (refs 28, 29, 30) under ambient conditions. The advancing contact angle was ≈40–42°, whereas the receding contact angle was ≈9–12° (ref. 39). Droplets were dispensed onto the heated surface whose temperature was monitored and recorded using a data acquisition system. A 25 μm diameter gold wire, functionalized with a 1 mM ethanol solution of 1H, 1H, 2H, 2H-perfluorodecanethiol (Sigma-Aldrich), was used to prevent lateral motion of the droplet outside of the imaging camera’s field of view.
Additional information
How to cite this article: Adera, S. et al. Non-wetting droplets on hot superhydrophilic surfaces. Nat. Commun. 4:2518 doi: 10.1038/ncomms3518 (2013).
References
Wenzel, R. N. Resistance of solid surfaces to wetting by water. Ind. Eng. Chem. 28, 988–994 (1936).
Quéré, D. Wetting and roughness. Annu. Rev. Mater. Res. 38, 71–99 (2008).
Bico, J., Thiele, U. & Quéré, D. Wetting of textured surfaces. Colloids surf. A: Physicochem. Eng. Asp. 206, 41–46 (2002).
Zheng, L., Wu, X., Lou, Z. & Wu, D. Superhydrophobicity from microstructured surface. Chin. Sci. Bull. 49, 1779–1787 (2004).
Liu, G., Fu, L., Rode, A. V. & Craig, V. S. Water droplet motion control on superhydrophobic surfaces: exploiting the Wenzel-to-Cassie transition. Langmuir 27, 2595–2600 (2011).
Zhang, T. et al. High-temperature wetting transition on micro- and nanostructured surfaces. Angew. Chem. Int. Ed. 50, 5311–5314 (2011).
Leidenfrost, J. G. De Aquae Communis Nonnullis Qualitatibus Tractatus. ([Typis Joan. Sebast. Straube, Acad. Typogr.] Impensis Hermanni Ovenni, Univers. bibliopolae, 1756).
Leidenfrost, J. G. On the fixation of water in diverse fire. Int. J. Heat Mass Trans. 9, 1153–1166 (1966).
Biance, A. L., Clanet, C. & Quéré, D. Leidenfrost drops. Phys. Fluids 15, 1632–1637 (2003).
Avedisian, C. & Koplik, J. Leidenfrost boiling of methanol droplets on hot porous/ceramic surfaces. Int. J. Heat Mass Trans. 30, 379–393 (1987).
Baumeister, K. J. & Hamill, T. D. Creeping flow solution of the Leidenfrost phenomenon. NASA TN D-3133 (1965).
Carey, V. P. Liquid-Vapor Phase-Change Phenomena. Hemisphere (1992).
Gottfried, B., Lee, C. & Bell, K. The Leidenfrost phenomenon: film boiling of liquid droplets on a flat plate. Int. J. Heat Mass Trans. 9, 1167–1188 (1966).
Kim, H., Truong, B., Buongiorno, J. & Hu, L. W. On the effect of surface roughness height, wettability, and nanoporosity on Leidenfrost phenomena. Appl. Phys. Lett. 98, 083121 (2011).
Aberle, C., Lewis, M., Yu, G., Lei, N. & Xu, J. Liquid marbles as thermally robust droplets: coating-assisted Leidenfrost-like effect. Soft Matt. 7, 11314–11318 (2011).
Muecke, U. P., Messing, G. L. & Gauckler, L. J. The Leidenfrost effect during spray pyrolysis of nickel oxide-gadolinia doped ceria composite thin films. Thin Solid Films 517, 1515–1521 (2009).
Elbahri, M., Paretkar, D., Hirmas, K., Jebril, S. & Adelung, R. Anti-lotus effect for nanostructuring at the Leidenfrost temperature. Adv. Mater. 19, 1262–1266 (2007).
Bernardin, J. & Mudawar, I. The Leidenfrost point: experimental study and assessment of existing models. J. Heat Trans. 121, 894–903 (1999).
Bernardin, J. D. & Mudawar, I. A cavity activation and bubble growth model of the Leidenfrost point. J. Heat Trans. 124, 864–874 (2002).
Kim, H., Buongiorno, J., Hu, L. W. & McKrell, T. Nanoparticle deposition effects on the minimum heat flux point and quench front speed during quenching in water-based alumina nanofluids. Int. J. Heat Mass Trans. 53, 1542–1553 (2010).
Kim, H., DeWitt, G., McKrell, T., Buongiorno, J. & Hu, L. On the quenching of steel and zircaloy spheres in water-based nanofluids with alumina, silica and diamond nanoparticles. Int. J. Multiphase Flow 35, 427–438 (2009).
Kim, S., Bang, I., Buongiorno, J. & Hu, L. Effects of nanoparticle deposition on surface wettability influencing boiling heat transfer in nanofluids. Appl. Phys. Lett. 89, 153107-153107-153103 (2006).
Arnaldo del Cerro, D. et al. Leidenfrost point reduction on micro-patterned metallic surfaces. Langmuir 28, 15106–15110 (2012).
Vakarelski, I. U., Patankar, N. A., Marston, J. O., Chan, D. Y. C. & Thoroddsen, S. T. Stabilization of Leidenfrost vapour layer by textured superhydrophobic surfaces. Nature 489, 274–277 (2012).
Vakarelski, I. U., Marston, J. O., Chan, D. Y. C. & Thoroddsen, S. T. Drag reduction by Leidenfrost vapor layers. Phys. Rev. Lett. 106, 214501 (2011).
Kruse, C. et al. Extraordinary shifts of the Leidenfrost temperature from multiscale micro/nanostructured surfaces. Langmuir 29, 9798–9806 (2013).
Quéré, D. Superhydrophobic surfaces: Leidenfrost becomes a fakir. Nat. Mater. 11, 915–916 (2012).
Kanta, A., Sedev, R. & Ralston, J. Thermally-and photoinduced changes in the water wettability of low-surface-area silica and titania. Langmuir 21, 2400–2407 (2005).
Yang, J., Duan, J., Fornasiero, D. & Ralston, J. Very small bubble formation at the solid-water interface. J. Phys. Chem. 107, 6139–6147 (2003).
Williams, R. & Goodman, A. M. Wetting of thin layers of SiO2 by water. Appl. Phys. Lett. 25, 531–532 (1974).
Deng, T. et al. Nonwetting of impinging droplets on textured surfaces. Appl. Phys. Lett. 94, 133109-133103 (2009).
Kwon, H.-M., Paxson, A. T., Varanasi, K. K. & Patankar, N. A. Rapid deceleration-driven wetting transition during pendant drop deposition on superhydrophobic surfaces. Phys. Rev. Lett. 106, 036102 (2011).
Hee Kwon, D. & Joon Lee, S. Impact and wetting behaviors of impinging microdroplets on superhydrophobic textured surfaces. Appl. Phys. Lett. 100, 171601 (2012).
Ou, J., Perot, B. & Rothstein, J. P. Laminar drag reduction in microchannels using ultrahydrophobic surfaces. Phys. Fluids 16, 4635 (2004).
Kutateladze, S. S. Fundamentals of Heat Transfer Academic Press: New York, (1963).
Brinkman, H. A calculation of the viscous force exerted by a flowing fluid on a dense swarm of particles. Appl. Sci. Res. 1, 27–34 (1949).
Brinkman, H. On the permeability of media consisting of closely packed porous particles. Appl. Sci. Res. 1, 81–86 (1949).
Sangani, A. & Acrivos, A. Slow flow past periodic arrays of cylinders with application to heat transfer. Int. J. Multiphase Flow 8, 193–206 (1982).
Raj, R., Maroo, S. C. & Wang, E. N. Wettability of graphene. Nano Lett. 13, 1509–1515 (2013).
Acknowledgements
We gratefully acknowledge funding support from Office of Naval Research (ONR) with Mark Spector as the program manager. We thank Professor Mikic for insightful discussion. We also acknowledge the MIT Microsystems Technology Laboratory for fabrication staff support and use of equipment. S.A. acknowledges support from the National Science Foundation Graduate Research Fellowship Program under Grant Number 1122374. Any opinion, findings and conclusions or recommendations expressed in this material are those of the authors(s) and do not necessarily reflect the views of the National Science Foundation. R.R. acknowledges support from Battelle’s National Security Global Business and R.E. acknowledges support from the Irish Research Council for Science, Engineering, and Technology, cofunded by Marie Curie Actions under FP7. Bell Labs Ireland thanks the Industrial Development Agency (IDA) Ireland for their financial support.
Author information
Authors and Affiliations
Contributions
S.A., R.R., R.E. and E.N.W. designed the experiment and developed the model, S.A. and R.R. carried out the experiments and all authors contributed with discussions, analysis and interpretation of experimental data. All authors wrote and edited the manuscript.
Corresponding author
Ethics declarations
Competing interests
The authors declare no competing financial interests.
Supplementary information
Supplementary Information
Supplementary Figures S1-S6, Supplementary Notes 1-2 and Supplementary References (PDF 631 kb)
Supplementary Movie 1
Dynamic behaviour of the typical non-wetting droplets investigated in our study. The video specifically corresponds to the data presented in Figure 2. During stage 1, the droplet is deposited and the temperature is maintained at 170 °C (stage 2) following which the sample is allowed to cool down and stabilized at 112 °C. The droplet at this steady state temperature evaporates (stage 3) until wetting transition and vigorous boiling at 34.3 s (stage 4). (AVI 16571 kb)
Rights and permissions
About this article
Cite this article
Adera, S., Raj, R., Enright, R. et al. Non-wetting droplets on hot superhydrophilic surfaces. Nat Commun 4, 2518 (2013). https://doi.org/10.1038/ncomms3518
Received:
Accepted:
Published:
DOI: https://doi.org/10.1038/ncomms3518
This article is cited by
-
Wettability studies of layer-by-layer films of Nafion/ Polyethylenemine/SiO2 nanoparticles
Journal of Polymer Research (2023)
-
Inhibiting the Leidenfrost effect above 1,000 °C for sustained thermal cooling
Nature (2022)
-
Self-cleaning of superhydrophobic nanostructured surfaces at low humidity enhanced by vertical electric field
Nano Research (2022)
-
Superlyophilic Interfaces Assisted Thermal Management
Chemical Research in Chinese Universities (2022)
-
Slippery damper of an overlay for arresting and manipulating droplets on nonwetting surfaces
Nature Communications (2021)
Comments
By submitting a comment you agree to abide by our Terms and Community Guidelines. If you find something abusive or that does not comply with our terms or guidelines please flag it as inappropriate.