Abstract
Controlling the propagation of intense optical wavepackets in transparent media is not a trivial task. During propagation, low- and high-order non-linear effects, including the Kerr effect, multiphoton absorption and ionization, lead to an uncontrolled complex reshaping of the optical wavepacket that involves pulse splitting, refocusing cycles in space and significant variations of the focus. Here we demonstrate both numerically and experimentally that intense, abruptly autofocusing beams in the form of accelerating ring-Airy beams are able to reshape into non-linear intense light-bullet wavepackets propagating over extended distances, while their positioning in space is extremely well defined. These unique wavepackets can offer significant advantages in numerous fields such as the generation of high harmonics and attosecond physics or the precise micro-engineering of materials.
Similar content being viewed by others
Introduction
Finite-energy Airy beams were first introduced in the field of optics in 2007 (refs 1, 2) as new non-diffracting wavepackets in one and two spatial dimensions. The Airy function, describing the spatial electric field profile of these beams, is the only non-spreading one-dimensional (1D) solution of the Schrödinger equation discovered in the field of quantum mechanics in 1976 (ref. 3). The most notable feature of the linear Airy beam is the transverse acceleration, which causes the beam to propagate in a parabolic trajectory4, while keeping a constant central lobe diameter. This exotic behaviour is forced by a strong spatial cubic phase which is imprinted on the beam profile. This spatial chirp causes a constant energy flux from the oscillating tail of the beam towards the main lobe, effectively forcing the beam to accelerate in the transverse direction. In addition, the Airy beam proves very resilient to perturbations, as it is able to linearly reconstruct (self-heal) itself5. Further research activity on Airy beams in the non-linear regime has revealed stationary non-linear 1D solutions6, (3+1)D non-linear light bullets7, solitons in self-defocusing media8 and other newly observed spatial mechanisms9,10. Recently, the Airy wavepacket concept has also been demonstrated for electron packets11.
The cylindrically symmetric Airy beam (or ring-Airy beam), which is able to abruptly autofocus in the linear regime, was introduced theoretically12 and was demonstrated experimentally13 to be able to deliver high-energy pulses inside thick transparent samples without damaging the material before the focus. The abrupt intensity increase at the focus of the ring-Airy makes it easy to combine a long working distance with a small focal volume. The remarkable abilities of the ring-Airy beam make it an ideal candidate for laser ablation applications in previously hard-to-reach environments.
Here we demonstrate that the non-linear dynamics of high-power ring-Airy wavepackets are even more impressive. Using numerical simulations, we compare the attributes of high-power ring-Airy wavepackets to those of Gaussian beams carrying the same power and identify a number of exciting features, which are very useful for practical applications14,15,16,17. These include a minor non-linear focal shift and the reshaping of the wavepacket into an intense non-linear dynamic light bullet structure. In addition, we elucidate the physical origin of these interesting features by correlating them to the typical ring-Airy spatiotemporal reshaping mechanism in the focus. Finally, our theoretical findings are confirmed by experiments in bulk fused silica.
Results
Non-linear ring-Airy beams
To explore the non-linear propagation dynamics of ring-Airy beams, we compare them with Gaussian beams. We consider two types of Gaussian beams that can be deemed equivalent to a given ring-Airy beam13, the equivalent envelope Gaussian beam (EEGB) defined as the Gaussian beam with full-width at half maximum (FWHM) equal to the diameter of the ring-Airy beam and the equivalent peak contrast Gaussian beam (ECGB), which, in the linear regime, reaches the same peak intensity contrast value at the focus (more details can be found in the beam description of the Methods section). The term peak contrast refers12 to the ratio of the peak intensity in the beam focus to the peak intensity at the beam origin. In our simulations, both beams are focused at the focus of the ring-Airy using a lens. Both of them carry the same power; thus, the EEGB and the ECGB only differ by their beam width and initial peak intensity. Regardless of the spatial profile of the beams used, the temporal profile in our simulations was in all cases Gaussian with a FWHM of 200 fs at a central wavelength of 800 nm. Additional information about the description of the simulated wavepackets and the numerical model used in the simulations can be found in the Methods section.
Focus shift in the non-linear regime
We performed numerical experiments by increasing the input power for all three beams. As expected, the focus is shifted towards the laser source as the input power is increased. Figure 1 shows a comparison of the position of the non-linear focus of the ring-Airy beam with those obtained for the two Gaussian beams. Interestingly, in the non-linear regime, the ring-Airy beam focus shift is significantly smaller compared with the two Gaussian beams as the beam power increases. For the ring-Airy, the focus position moves from 24 cm to roughly 22 cm, whereas the input power is gradually increased up to 10 Pcr (Pcr being the critical power for self-focusing, see Methods for exact definition). Further increase in power, up to 24 Pcr, seems to have a negligible effect on the focus position. For both Gaussian beams, the focus shift is much larger compared with the ring-Airy case. Especially for the ECGB, the focus position is shifted down to 11 cm for 24 Pcr, which is more than half the initial distance. For the EEGB, the focus shift is not as strong, but still reaches 6 cm, that is, about three times more than for the ring-Airy case. The difference between the two Gaussian beams is explained by the wider beam width for the EEGB and the fact that the non-linear focus position is proportional to the Rayleigh length, that is, scales as (w02)18,19. In the Discussion section below, we provide an analytical approach for calculating precisely the small focus shift of the ring-Airy beams.
Spatial dynamics and filament formation
The peak intensity of the ring-Airy beam is shown in Fig. 2a as a function of the propagation distance for five different input powers. As the input power is increased, the distribution of the peak intensity along the beam propagation changes significantly, showing an escalating abrupt increase near the focus. For example, at 5 Pcr, the first peak appears much more abruptly and the consecutive secondary peaks, although spatially separated in the linear regime, merge into an almost uniform filament sustaining high peak intensities over a longer propagation distance, compared with the linear case (black continuous line). As the power is gradually increased and non-linearities come into play, the secondary peaks gradually merge and rise in intensity until the formation of a continuous intensity plateau at Pin>10 Pcr. At these powers, the peak intensity is almost constant ≅2.5 × 1013 W cm−2 along the plateau, without significantly increasing as the input power is further increased. This can be understood in terms of intensity clamping20 due to the presence of non-linear losses, which are strong enough to limit the increase of the peak intensity. The resulting structure is a long filament similar to filaments obtained by propagation of high-power Gaussian beams18, except that it results from the collapse of a ring-Airy beam as detailed below. This is clearly demonstrated in Fig. 2b, where the peak intensity of a ring-Airy beam at the plateau region (z=40 cm) is shown in comparison with two Gaussian beams as a function of the input power. The peak intensity for all beams is practically identical for input powers above 5 Pcr. A graphic representation of the transformation of a ring-Airy beam, where the discrete sharp intensity peaks in the linear regime transform into a uniform filament in the non-linear regime, is shown in Fig. 2c.
Spatiotemporal effects and light bullet formation
Besides the minor focal shift and the formation of a filament, interesting spatiotemporal dynamics take place beyond the focal region. Figure 3 depicts the intensity isosurfaces for an EEGB (first row), an ECGB (second row) and a ring-Airy wavepacket (third row) for various propagation distances beyond the non-linear focus.
Each of the three wavepackets carries ten critical powers. Because of the different non-linear dynamics (Fig. 1), the actual focus position (denoted as 0 cm in Fig. 3) along the propagation axis is different for each beam.
The two Gaussian beams exhibit a typical severe spatiotemporal reshaping process extensively studied in the literature18,21. As shown in Fig. 3, the initial Gaussian wavepacket is reshaped into a ring structure with an intense spot that is split in the temporal domain. We can clearly see that for both cases the space and time distributions of the wavepacket are constantly evolving in a complex way, as expected in filamentation of Gaussian beams. The dynamic reshaping action of non-linear effects diminishes after ∼15 cm. After this point, both Gaussian wavepackets spread owing to linear diffraction and dispersion.
On the other hand, the spatiotemporal dynamics of the ring-Airy beam are very different. The wavepacket has the form of a ring with an intense core in its centre, whereas no pulse splitting is obtained in the temporal domain. This non-linear light-bullet structure propagates without significant changes over 15 cm. Only after 18 cm of propagation, the non-linear dynamics start to weaken and the ring-Airy wavepacket starts to spread due to the action of diffraction and dispersion. The annular structure that surrounds the ring-Airy intense peak at 15 cm after the focus, although resembles a similar annular feature formed in the Gaussian wavepacket, is generated by different mechanisms. In the case of the non-linear ring-Airy beam, the ring is sustained by the combination of the pre-organized energy flux from the tail to the main lobe of the Airy profile12,13 and light coming from the non-linear focus, diffracted by the generated plasma. In the case of the Gaussian beam, the ring is generated by a spontaneous transformation of the Gaussian beam into a Bessel-like beam induced by non-linear effects22 and featured by conical emission23. This type of non-linear ring formation depends on the multiphoton order of the non-linear absorption and is discussed in details in the case of two-photon absorption in ref. 24.
Experimental demonstration
To confirm the validity of the simulation findings, we performed non-linear propagation experiments of ring-Airy beams in fused silica. The use of fused silica is beneficial both in terms of the energy needed (Pcr is much lower than air) and also in the visualization of the non-linear propagation by exploiting the accompanying two-photon red fluorescence emission25. Detailed information about the experimental procedure and the analysis used to estimate the intensity profile of the ring-Airy beam can be found in the Methods section. Typical non-linear fluorescence emission images are shown in Fig. 4a. It is clearly visible that the non-linear focus shifts as the input energy is increased. Furthermore, low-intensity secondary peaks, characteristic to the ring-Airy, are emerging after the primary focus. The experimentally measured intensity distribution along the propagation axis I(0,z) for various ring-Airy input energies is depicted in Fig. 4b.
As predicted by the theoretical simulations in the non-linear propagation regime, the consecutive peak contrast is reduced as the beam energy is increased. At high-enough energies, the intensity maxima are merged to a single intense filament along the propagation axis. This trend is verified in Fig. 4c by numerical simulations we performed in fused silica for the same input parameters as in the experiments. One may also note in both experiments and simulations the gradual decrease of the focus shift with increasing input energy as with the simulations in air above.
Discussion
An important question to answer for the purpose of predicting the position of the focus in a given experimental situation (as the one shown in Fig. 2a) is what is the mechanism leading to the small non-linear focus shift for the ring-Airy, and, even more importantly, can a scaling law be derived?
As the spatial profile of the ring-Airy beam is significantly different from that of a typical Gaussian beam, the well-known Marburger’s formula19 cannot be used to predict the collapse distance. The collapse of a ring-Airy beam can be described in two stages: (i) a quasi-linear stage, during which the ring structure shrinks over a propagation distance fmin and follows a parabolic trajectory (see Methods section, equation (4)); (ii) a second stage from fmin to the collapse distance frAi, during which the intensity of the ring-Airy beam increases more abruptly and the assumption of a quasi-1D trajectory for the peak intensity no longer holds. This happens when the primary ring reaches a sufficiently small diameter to induce significant mutual attraction between opposite parts of the ring, in analogy with the mutual attraction and merging of two individual filaments induced by cross Kerr effects when they are separated by less than approximately three typical filament diameters26. Pursuing this analogy, we assume that in the case of ring-Airy beams as well, non-linear effects will take over when the diameter of the primary ring is ∼3 times that of the diameter of a typical filament in the medium.
Using equation (4) from the Methods section, we can estimate the propagation distance fmin from the condition R(fmin)=3wα/2:
where wα≅90 μm is the typical filament diameter in air and R0∼980 μm.
In our case, the ring-Airy focus in the linear regime is f=23.95 cm. For the second stage, a simple empirical formula that fits nicely the simulation results for the non-linear focus shift as a function of the ring-Airy input power Pin is given by:
where Pcr refers to the critical power19 of a Gaussian beam with the same central wavelength and γ≡PRing/Pin is a scaling parameter referring to the fraction of power contained in the primary ring of the ring-Airy distribution. The quantity f−fmin corresponds to the maximum shift that can be reached at very large powers, where the optical Kerr effect abruptly focuses on the primary ring. A comparison of the focus shift estimated by our numerical simulations and the prediction of the empirical formula of equation (2) is shown in Fig. 5a.
To confirm that equation (2) adequately predicts the non-linear focus position for different ring-Airy beams, we have performed simulations for a range of ring-Airy beam parameters (different radii and widths). The predicted and simulated focus position for various ring-Airy beams is shown in the inset of Fig. 5a. In all cases, equation (2) clearly predicts the focus position of the ring-Airy beam. To further validate equation (2) we compare its prediction in Fig. 5b, against the measured focus shift as a function of the input energy for the experimentally generated ring-Airy beam in fused silica (see Fig. 4a). Again, although the propagation medium is now different, the theoretical prediction using equation (2) clearly fits the experimental findings.
In conclusion, ring-Airy wavepackets present unique features in the non-linear regime. The non-linear focus shift, as the beam power is increased, is much smaller for a ring-Airy beam compared with equivalent Gaussian beams and can be precisely predicted with a simple semi-empirical formula we derived considering the Kerr-induced ring collapse. Although, the most exciting feature is that beyond the focal region, the otherwise localized, in the linear regime, ring-Airy wavepacket is reshaped into an intense non-linear light bullet. Finally, we have also offered the first experimental demonstration of these predictions performing experiments in fused silica. The level of control achieved with these wavepackets offers unique advantages for applications that require regulated paths of high intensities, such as harmonic generation, laser micromachining and remote sensing.
Methods
Beam description
Three different laser beam profiles were used in the simulations, a ring-Airy beam and two Gaussian beams. All simulations were done in air at atmospheric pressure. The ring-Airy beam electric field13 is described by the following equation:
where Ai() corresponds to the Airy function3, r is the radial coordinate, r0 represents the radius of the primary ring, α is a truncation constant and w is a scaling factor. More precisely, the primary ring of the beam has its peak intensity at a radius of R0≡r0–w·g(α), where g(α) denotes the first zero of the function Ai′(x)+α·Ai(x), whereas its FWHM is ∼2.28 w (ref. 13). The power content carried by the beam is numerically calculated by integration of the starting spatial intensity profile over the whole computational box (5 mm radius). The linear focus of the ring-Airy beam can be analytically described by the beam parameters , by considering large ring-Airy beams as quasi-1D structures, that is, the trajectory of the intensity maximum of the ring-Airy beam in the linear regime is given by the quadratic acceleration for the 1D Airy beams1,13:
In our simulations, we used r0=921 μm, w=61.4 μm and α=0.05, leading to g(α)∼−0.97. Using these parameters, the ring-Airy beam is autofocusing at a position z=23.95 cm. The widths at 1/e2 radius of the EEGB and ECGB are 1,738 and 855 μm, respectively. Figure 6 shows the radial intensity distribution of the ring-Airy and both Gaussian beams.
Numerical model
The numerical model18 that is used in the simulations resolves a non-linear envelope equation governing the propagation along the z direction of the pulse envelope E(r,z,t) in cylindrical coordinates. It takes the form of a canonical unidirectional propagation equation in the generalized few-cycle envelope approximation21,27 and reads in the Fourier domain:
the first (linear) term on the right-hand side includes the effects of diffraction, dispersion and space–time coupling: , where and the dispersive properties of the medium are described by a Sellmeier relation k(ω) for air28, and denote the carrier wavenumber at the central frequency ω0, the linear refractive index in air at ω0 and .
The non-linear dispersion function describes the self-steepening operator where the non-linear polarization represents the optical Kerr effect, c is the speed of light in vacuum and ɛ0 is the vacuum permittivity. The derivation is explained in details in ref. 21. The non-linear terms in equation (1) are all included in the non-linear polarization envelope and current envelope , which are calculated in the space–time (τ,r,z) domain, where denotes time in the local pulse frame. The non-linear polarization describes the optical Kerr effect:
where the coefficient for the Kerr non-linearity in air n2=3.2 × 10−19 cm2 W−1 leads to a critical power for self-focusing ∼3.2 GW.
The current describes plasma absorption and plasma defocusing in the framework of the Drude model, with collision time τc:
where ρ denotes the density of the plasma generated by multiphoton ionization and avalanche. The various parameters in equations (6) and (7) are the cross section for inverse Bremsstrahlung =5.5 × 10−20 cm2 calculated from the Drude model with the collision time τc=350 fs in air, the cross section for multiphoton absorption βK=Kħω0ρntσK=4 × 10−95 cm13 W−7, and σK=3.4 × 10−96 cm16 W−8 s−1 denotes the coefficient for multiphoton ionization with K=8 photons at 800 nm for ionizing oxygen molecules with an initial density ρnt=0.5 × 1018 cm−3.
Equation (5) is coupled with an evolution of equation (8) for the electron density, which describes plasma generation by multiphoton ionization with rate WMPI=σKIK and avalanche:
Ui=12.03 eV denotes the ionization potential of oxygen molecules.
Experimental implementation
As shown in Fig. 7, we used 160 fs, 800 nm laser pulses, with a Gaussian spatiotemporal distribution, produced by a 50-Hz Ti:Sapphire laser system. To generate the ring-Airy beam, we followed a Fourier transform approach described in detail in ref. 13. In brief, the method is based on modulating the phase of a Gaussian beam (using a Hamamatsu LCOS-X10468-2 phase reflecting only spatial light modulator), which is then Fourier transformed by a lens. The ring-Airy distribution is then generated in the Fourier transform plane of the lens after blocking the zero-order diffraction. To further reduce the effective focal length of the generated ring-Airy beam, we reduced its transverse size by ∼17 times, using a 4f optical system composed by a 300-mm lens and a × 8 (0.2 numerical aperture) microscope objective.
The red fluorescence emission, induced by the high intensity of the ring-Airy beam in the focus region, was imaged using a compact microscope system (0.2 numerical aperture) and a linear charge-coupled device camera (12 bit, 1,224 × 968 pixels). Using the fluorescence emission images, we were able to estimate the intensity distribution of the propagating beam. More specifically, the observed fluorescence is actually an Abel transform of a radially symmetric fluorescence emission in the focal volume. By applying inverse Abel transform on the images, we estimate the radial distribution of the fluorescence emission F(r,z). The beam intensity I(r,z) distribution can be then extracted from F(r,z)I2(r,z). Although this method does not provide an absolute estimation of the beam intensity, it can be used to accurately estimate its spatial distribution.
Additional information
How to cite this article: Panagiotopoulos, P. et al. Sharply autofocused ring-Airy beams transforming into non-linear intense light bullets. Nat. Commun. 4:2622 doi: 10.1038/ncomms3622 (2013).
References
Siviloglou, G. A. & Christodoulides, D. N. Accelerating finite energy Airy beams. Opt. Lett. 32, 979–981 (2007).
Siviloglou, G. A., Broky, J., Dogariu, A. & Christodoulides, D. N. Observation of accelerating airy beams. Phys. Rev. Lett. 99, 213901 (2007).
Berry, M. V. & Balazs, N. L. Nonspreading wave packets. Am. J. Phys. 47, 264–267 (1979).
Siviloglou, G. A., Broky, J., Dogariu, A. & Christodoulides, D. N. Ballistic dynamics of Airy beams. Opt. Lett. 33, 207–209 (2008).
Broky, J., Siviloglou, G. A., Dogariu, A. & Christodoulides, D. N. Self-healing properties of optical Airy beams. Opt. Express 16, 12880–12891 (2008).
Lotti, A. et al. Stationary nonlinear Airy beams. Phys. Rev. A 84, 021807 (2011).
Abdollahpour, D., Suntsov, S., Papazoglou, D. G. & Tzortzakis, S. Spatiotemporal Airy light bullets in the linear and nonlinear regimes. Phys. Rev. Lett. 105, 253901 (2010).
Kaminer, I., Segev, M. & Christodoulides, D. N. Self-Accelerating Self-Trapped Optical Beams. Phys. Rev. Lett. 106, 213903 (2011).
Panagiotopoulos, P. et al. Nonlinear propagation dynamics of finite-energy Airy beams. Phys. Rev. A 86, 013842 (2012).
Polynkin, P., Kolesik, M., Moloney, J. V., Siviloglou, G. A. & Christodoulides, D. N. Curved plasma channel generation using ultraintense Airy beams. Science 324, 229–232 (2009).
Voloch-Bloch, N., Lereah, Y., Lilach, Y., Gover, A. & Arie, A. Generation of electron Airy beams. Nature 494, 331–335 (2013).
Efremidis, N. K. & Christodoulides, D. N. Abruptly autofocusing waves. Opt. Lett. 35, 4045–4047 (2010).
Papazoglou, D. G., Efremidis, N. K., Christodoulides, D. N. & Tzortzakis, S. Observation of abruptly autofocusing waves. Opt. Lett. 36, 1842–1844 (2011).
Bhuyan, M. K. et al. High aspect ratio taper-free microchannel fabrication using femtosecond Bessel beams. Opt. Express 18, 566–574 (2010).
Bhuyan, M. K. et al. High aspect ratio nanochannel machining using single shot femtosecond Bessel beams. Appl. Phys. Lett. 97, 081102 (2010).
Juodkazis, S. et al. Laser-induced microexplosion confined in the bulk of a sapphire crystal: evidence of multimegabar pressures. Phys. Rev. Lett. 96, 166101 (2006).
Kasparian, J. et al. White-Light filaments for atmospheric analysis. Science 301, 61–64 (2003).
Couairon, A. & Mysyrowicz, A. Femtosecond filamentation in transparent media. Phys. Rep. 441, 47–189 (2007).
Marburger, J. H. Self-focusing: theory. Prog. Quantum Electron. 4, (Part 1): 35–110 (1975).
Becker, A. et al. Intensity clamping and re-focusing of intense femtosecond laser pulses in nitrogen molecular gas. Appl. Phys. B 73, 287–290 (2001).
Couairon, A. et al. Practitioner’s guide to laser pulse propagation models and simulation. Eur. Phys. J. Spec. Top. 199, 5–76 (2011).
Dubietis, A., Gaizauskas, E., Tamosauskas, G. & Di Trapani, P. Light filaments without self-channeling. Phys. Rev. Lett. 92, 253903 (2004).
Faccio, D. et al. Ultrashort laser pulse filamentation from spontaneous X Wave formation in air. Opt. Express 16, 1565–1570 (2008).
Faccio, D. et al. Kerr-induced spontaneous Bessel beam formation in the regime of strong two-photon absorption. Opt. Express 16, 8213–8218 (2008).
Papazoglou, D. G. & Tzortzakis, S. Physical mechanisms of fused silica restructuring and densification after femtosecond laser excitation. Opt. Mater. Express 1, 625–632 (2011).
Tzortzakis, S. et al. Breakup and fusion of self-guided femtosecond light pulses in air. Phys. Rev. Lett. 86, 5470–5473 (2001).
Kinsler, P. & New, G. H. C. Few-cycle pulse propagation. Phys. Rev. A 67, 023813 (2003).
Peck, E. R. & Reeder, K. Dispersion of air. J. Opt. Soc. Am. 62, 958–962 (1972).
Acknowledgements
This work was supported by the THALES project ‘ANEMOS’ and Aristeia project ‘FTERA’ (grant number 2570), cofinanced by the European Union and Greek National Funds.
Author information
Authors and Affiliations
Contributions
All authors have contributed to the development and/or implementation of the concept. P.P. and A.C. performed the simulations, D.G.P. and S.T. designed and performed the experiments, and S.T. supervised the research. All authors contributed to the discussion of the results and to the writing of the manuscript.
Corresponding author
Ethics declarations
Competing interests
The authors declare no competing financial interests.
Rights and permissions
About this article
Cite this article
Panagiotopoulos, P., Papazoglou, D., Couairon, A. et al. Sharply autofocused ring-Airy beams transforming into non-linear intense light bullets. Nat Commun 4, 2622 (2013). https://doi.org/10.1038/ncomms3622
Received:
Accepted:
Published:
DOI: https://doi.org/10.1038/ncomms3622
This article is cited by
-
Clusters of rotating beams with autofocusing and transformation properties generated by a spatial light modulator
Applied Physics B (2023)
-
Sum-frequency generation of ring-Airy beams
Applied Physics B (2022)
-
Optimized anti-reflection core-shell microspheres for enhanced optical trapping by structured light beams
Scientific Reports (2021)
-
Generation and control of dynamically tunable circular Pearcey beams with annular spiral-zone phase
Science China Physics, Mechanics & Astronomy (2021)
-
Generating arbitrary arrays of circular Airy Gaussian vortex beams with a single digital hologram
Applied Physics B (2021)
Comments
By submitting a comment you agree to abide by our Terms and Community Guidelines. If you find something abusive or that does not comply with our terms or guidelines please flag it as inappropriate.