Correction to: Scientific Reports https://doi.org/10.1038/s41598-021-81861-w, published online 28 January 2021
The original version of this Article contained errors.
Firstly, Shaul Avraham and Yair Yacobi were omitted from the author list in the original version of this Article.
The Author Contributions section now reads:
V.P., G.M.-K. were involved in the experimental protocols, including the specimens’ fabrication, preparation and characterization of them. A.K.-D. made the XRD examination and together with A.S., contributed to results interpretation. S. A., Y. Y. contributed to the research formulation, provided scientific advice and supervision. N.T., A.F., and S.G. provided scientific advice and supervision. All authors have contributed to the writing of this article.
Secondly, Affiliation 2 were incorrectly given as ‘Heat Treatment and Physics of Metals Department, Ural Federal University, Ekaterinburg, Russia.’ The correct affiliation is listed below:
Institute of New Materials and Technologies, Ural Federal University, Ekaterinburg, Russia
Thirdly, the Affiliations given for Vladimir Popov were incomplete. The correct affiliations are listed below:
Israel Institute of Metals, Technion, Israel Institute of Technology, 3200003, Haifa, Israel
Institute of New Materials and Technologies, Ural Federal University, Ekaterinburg, Russia
Fourthly, the incorrect email address for Vladimir Popov was quoted. Correspondence and requests for materials should be addressed to vvp0604@gmail.com.
Lastly, the Acknowledgements section was incomplete.
“This work performed in the frame of ITHACA, the COST INNOVATORS' GRANT, supported by COST (European Cooperation in Science and Technology). All authors greatly acknowledge the financial support provided by the UKRI via Grants No. EP/L016567/1, EP/S013652/1, EP/S036180/1, EP/T001100/1 and EP/T024607/1, Royal Academy of Engineering via Grants No. IAPP18-19\295, TSP1332 and EXPP2021\1\277, EU Cost Action (CA15102, CA18125, CA18224 and CA16235) and Newton Fellowship award from the Royal Society (NIF\R1\191571). SG is particularly thankful to European Regional Development Funds (ERDF) sponsored A2i project at LSBU that have catalysed several industrial partnerships.”
now reads:
“This research was funded by the NRCN. This work performed in the frame of ITHACA, the COST INNOVATORS' GRANT, supported by COST (European Cooperation in Science and Technology). All authors greatly acknowledge the financial support provided by the UKRI via Grants No. EP/L016567/1, EP/S013652/1, EP/S036180/1, EP/T001100/1 and EP/T024607/1, Royal Academy of Engineering via Grants No. IAPP18-19\295, TSP1332 and EXPP2021\1\277, EU Cost Action (CA15102, CA18125, CA18224 and CA16235) and Newton Fellowship award from the Royal Society (NIF\R1\191571). SG is particularly thankful to European Regional Development Funds (ERDF) sponsored A2i project at LSBU that have catalysed several industrial partnerships.”
The original Article has been corrected.
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons licence, and indicate if changes were made. The images or other third party material in this article are included in the article's Creative Commons licence, unless indicated otherwise in a credit line to the material. If material is not included in the article's Creative Commons licence and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this licence, visit http://creativecommons.org/licenses/by/4.0/.
About this article
Cite this article
Popov, V., Fleisher, A., Muller‑Kamskii, G. et al. Author Correction: Novel hybrid method to additively manufacture denser graphite structures using Binder Jetting. Sci Rep 12, 1644 (2022). https://doi.org/10.1038/s41598-022-05818-3
Published:
DOI: https://doi.org/10.1038/s41598-022-05818-3
Comments
By submitting a comment you agree to abide by our Terms and Community Guidelines. If you find something abusive or that does not comply with our terms or guidelines please flag it as inappropriate.