Abstract
Graphene devices for radio frequency (RF) applications are of great interest due to their excellent carrier mobility and saturation velocity. However, the insufficient current saturation in graphene field effect transistors (FETs) is a barrier preventing enhancements of the maximum oscillation frequency and voltage gain, both of which should be improved for RF transistors. Achieving a high output resistance is therefore a crucial step for graphene to be utilized in RF applications. In the present study, we report high output resistances and voltage gains in graphene-on-silicon (GoS) FETs. This is achieved by utilizing bare silicon as a supporting substrate without an insulating layer under the graphene. The GoSFETs exhibit a maximum output resistance of 2.5 MΩ∙μm, maximum intrinsic voltage gain of 28 dB, and maximum voltage gain of 9 dB. This method opens a new route to overcome the limitations of conventional graphene-on-insulator (GoI) FETs and subsequently brings graphene electronics closer to practical usage.
Similar content being viewed by others
Introduction
The enormous interest in graphene for electronic device applications originates from its outstanding charge transport properties and atomic-scale thickness1,2,3. However, graphene devices suffer from poor on/off current ratios, which are caused by a zero band gap property. This limits their applications in logic transistors. Nevertheless, owing to graphene’s exceptionally high carrier mobility and saturation velocity, it is a strong candidate for RF device applications, since RF transistors do not have to be switched off in operating conditions1,4,5.
Intensive research activities examining graphene RF FETs thus far have mainly focused on achieving higher cut-off frequencies (fT) with the help of gate length scaling6. Recently, fT values as high as 400 GHz were reported from state-of-the-art graphene RF FETs7,8,9,10,11,12,13,14,15,16. However, from a circuit designer’s point of view, rather than fT, the maximum oscillation frequency (fmax) and intrinsic voltage gain (AV0) are more important factors for RF devices1, and very recently fmax values as high as 105 GHz were reported17. The poor fmax and AV0 values of conventional GoIFETs mainly originate from the absence of current saturation in the output characteristics due to the absence of a band gap and the Klein tunneling effect18.
It is therefore highly desirable to obtain robust current saturation in the output characteristics from graphene FETs, which would result in a higher fmax and AV019,20,21. FET current saturation can be observed, either due to the decrease of carrier density in the channel near the drain side or to the velocity saturation of the carriers caused by phonon scattering22. For non-zero band gap semiconductors such as Si, a depletion region is formed at the drain side under VGS − VTH = VDS, and the width of the depletion region extends as VDS increases, where VGS is the gate-to-source voltage, VTH is the threshold voltage, and VDS is the drain-to-source voltage. On the other hand, zero band gap materials such as graphene do not form depletion regions in the channel. Rather than forming a depletion region, a different polarity charge is generated at the drain side, and this charge extends as VDS increases. This generation of other charged carriers in the channel leads to the presence of a kink-like feature in the output curve of the GoIFETs, resulting in lower output resistance (ro) and thereby degraded RF performance. Thus, by suppressing the generation of the other charged carrier in the channel near the drain, the graphene device is able to obtain a higher ro.
One of the methods that has been attempted to suppress the generation of the other charged carriers is the strengthening of the gate electrostatic control. In other words, the influence of the drain voltage is weakened with respect to the graphene channel near the drain side. Thus, previous attempts have focused on increasing the gate coupling by increasing the gate capacitance19,20,21 and/or minimizing the residual carrier concentration (n0)22,23.
Recently, hexagonal boron nitride (h-BN) has been adopted as a bottom gate dielectric to minimize n022,23 since h-BN exhibits lower charged impurities and provide higher optical phonon energy than a conventional SiO2 substrate19,23. The minimum n0, which was proportional to the charged impurities, disorder, and thermal excitation, was found to significantly affect the drain conductance ()24,25. Despite the importance of obtaining current saturation in the output characteristics, robust current saturation has not yet been demonstrated in graphene FETs that offer highly compatible integration with current transistor processes.
In this study, we present simple but improved output characteristics by utilizing silicon instead of conventional SiO2 or h-BN as a substrate. The implementation of Si as a substrate material for graphene has additional advantages over h-BN and other insulators in that the integration in wafer-sized scales is comparable to conventional FET technologies. Several other groups have also reported that graphene transfers onto Si surfaces, but their studies focused on the formation of a Schottky junction to modulate the current, which entails charge transport vertically from the graphene to silicon26,27,28. Moreover, their devices still suffered from poor output resistance. In contrast to previous approaches28, in this work the charged carriers only move through the graphene layer. In other words, the current flows in a horizontal direction parallel to the silicon surface, and the carriers are confined within the graphene. The proposed device shows improved output resistance.
The typical architecture of a GoSFET is shown in Fig. 1a. The only difference between the GoSFET and conventional GoIFETs is the absence of an oxide layer under the graphene. Due to the lack of an insulating layer under the graphene in GoSFETs, the potential in the graphene is strongly affected by the charge carrier density and carrier type of the Si substrate. Figure 1b shows typical GoSFET transfer characteristics at both VDS = 1 V and VDS = −1 V, where lightly doped n-type silicon was used as a substrate. Excellent transfer characteristics were observed under VDS = −1 V, where the charge in the Si was depleted at the drain side due to the reverse bias condition, as shown in the inset of Fig. 1b. Unlike the reverse bias condition at VDS = −1 V, the performance of the GoSFET degraded under VDS = 1 V due to the non-negligible contribution of the body current, IB, which was caused by the forward bias condition. A further investigation of IB, depending on the type of Si substrate, was conducted, and the results are shown in Fig. 1c,d. In Fig. 1c, IB is 105 times lower than the drain current (ID), indicating that the silicon substrate successfully acted as an insulator under the reverse bias condition. In contrast to the reverse bias condition at VDS < 0 (Fig. 1c), the electrons in the body flowed to the graphene, and IB became comparable to ID under the forward bias condition at VDS > 0 (Fig. 1d). IB should be suppressed in the output characteristics. The doping type of the Si substrate thus should be considered depending on the operating voltage conditions to form a depletion region in the channel near the drain side, as shown in the inset of Fig. 1d.
Figure 2a shows typical GoSFET output characteristics, revealing improved current saturation in a wide drain voltage range. Unlike the improved current saturation in the GoSFETs, current saturation in a narrow drain voltage range was observed in the output characteristics of the conventional GoIFETs in Fig. 2b, which is typical in graphene FETs. The contour plots of gds in Fig. 2c,d clearly show that the current saturation of the GoSFETs is much more robust than that of the conventional GoIFETs. The improved drain current saturation in the GoSFETs results in a lower gds and higher output resistance, as shown in Fig. 2e. The maximum ro at a given VGS is plotted in Fig. 2f, showing that a ro value as high as 2.5 MΩ∙μm was obtained from the GoSFETs, in contrast to the ro value of 0.12 MΩ∙μm obtained from the GoIFETs. This improved GoSFET drain current saturation is mainly attributed to the suppression of electron carrier generation as the drain voltage increases, which is described in Fig. 3b,c. The potential energy of the drain is coupled with the energy level of the Si substrate. Thus, the positive fixed charge is generated in the depletion region near the drain side. This additional potential from the Si substrate allows a higher graphene energy level and thus the graphene is able to maintain its p-type behavior even at higher drain voltages. On the other hand, in the GoIFETs, other polarity carriers are generated near the drain side at higher drain voltages, which causes the kink effect in the GoIFETs, as shown in Fig. 3a–c. It is worth noting that the current takeoff at high drain voltage in the GoSFET is steeper than that in the GoIFET. The surface potential at the onset of the strong inversion in the Si at high drain voltage leads to a hole inversion layer, generating a mobile carrier charge and eventually contributing to the drain current, as shown in Fig. 3d.
The cumulative results of the maximum ro in Fig. 4a clearly show that, in terms of the RF characteristics, the GoSFETs outperformed the conventional GoIFETs due to the higher ro. We further investigated the correlation between the maximum ro and several device parameters, including the residual carrier concentration, n0, contact resistance, RC, and FET carrier mobility, μ, as shown in Fig. 4b–d. Their values were extracted from the fitting using the model (Equation (1) in the supplementary information) for both the GoSFETs and GoIFETs29. It was found that both n0 and RC were inversely proportional to the maximum ro in logarithmic scale, especially for the GoSFETs, as shown in Fig. 4b,c. The robust current saturation required strong gate coupling, which could be obtained at low parasitic capacitance, i.e., a low n017,24. Generally, low GoSFET values are attributed to the non-polar property of the silicon surface, which suppresses residual impurities between the graphene and the silicon surface. Unlike on the silicon surface, charged residues can easily attach to the SiO2 surface (polar behavior), which results in the doping of the graphene and degradation of the graphene devices30. The residual charges on the SiO2 were reported to be around 2 ~ 5 × 1011cm−2, while those on the silicon surface were around 0.3 ~ 2.8 × 1010 cm−231,32, which were also verified by the Raman analysis as shown in the supplementary (Fig. S2). The experimental results indicated that there are more residual charges on graphene/SiO2 than graphene/Si interfaces.
The suppression capabilities that prevent the generation of the other polarity carrier in the channel near the drain are directly affected by the electron potential energy in the Si, which is influenced by the metal/graphene voltage drop. Therefore, it is expected that the maximum ro is inversely proportional to RC for the GoSFETs, while ro exists irrespective of RC for the GoIFET. The lower contact resistance in the GoSFETs compared to that of the GoIFETs is attributed to the presence of additional charge injection into the graphene from the Si bottom substrate, in addition to the metal pad. Both Pd and Si atoms are able to inter-diffuse through the defects in the graphene, such as carbon atom vacancies, thereby form a conductive Pd silicide (Fig. S1) in the Si substrate33, which is the source of the additional charge injection into the graphene. The lower contact resistance of the graphene devices is inter-correlated with the higher FET mobility in the GoSFETs. Finally, a weak correlation between the maximum ro and μ can be observed in Fig. 3d. Nevertheless, it is evident that the FET mobility of GoSFETs is higher than that of GoIFETs due to the higher phonon energy of Si (63 meV) compared to that of SiO2 (50 meV)34,35.
Figure 5a shows that the maximum ro was proportional to the maximum AV0, and that a maximum AV0 as high as 28 dB was achieved from the GoSFETs, which is comparable to that of Si-based RF FETs. In order to verify the performance of the voltage amplifier, a common-source voltage amplifier was implemented with a P-GoSFET, as shown in Fig. 5b. The voltage amplifier showed excellent voltage amplification behavior, as presented in Fig. 5c. A maximum AV as high as 9 dB was obtained at a load resistance (RD) of 50 kΩ (Fig. 5d).
In summary, the utilization of a silicon substrate in graphene FETs without an insulating layer leads to robust current saturation under wide-ranging and exceptionally high output resistance. In addition, the proposed GoSFETs show excellent process compatibility with conventional FET processes. This method potentially can enable the implementation of graphene in RF device applications.
Methods
Device fabrication
The graphene used in this work was synthesized using the inductive coupling plasma chemical vapor deposition method on a thin copper film, and it was transferred using the typical wet transfer method with PMMA. For the conventional GoIFETs, the graphene was transferred onto thermally grown SiO2 (100 nm) on a heavily doped p-type silicon wafer (resistivity of ~0.01–0.05 Ω∙cm). For the GoSFETs, the thermal oxide (50 nm) in the active region on lightly doped n- or p-type silicon (resistivity of ~1–5 Ω∙cm) was patterned using a buffered oxide etchant, and the graphene was transferred immediately after the removal of the photoresist and the native oxide. The subsequent processes were identical for both the GoSFETs and GoIFETs. After patterning the channel graphene, the source and drain were defined using a Pd (5 nm)/Au (50 nm) lift-off process. Next, 20 nm of Al2O3 was deposited by atomic layer deposition (ALD) process on the graphene surface. Prior to the ALD process, 0.5 nm aluminum layer was evaporated on the graphene surface as a nucleation layer. The ultra-thin aluminum nucleation layer is soon oxidized during the ALD process. The 150 nm Al gate metal was formed using a thermal evaporator and the lift-off process. Finally, the device went through a thermal budget of 300 °C for 12 hrs.
Electrical measurement
All of the devices were measured at room temperature in ambient air with a B1500 parameter analyzer. In order to implement a common source voltage amplifier with a graphene–on–silicon transistor, the external resistances (RG = 1 MΩ, RD = 10, 30, 50 kΩ) and capacitor (CG = 1 μF) set on a breadboard, as well as a DC supplier and function generator, were connected. The transistors were staged in a probe station and connected to the circuit with a biaxial cable. The input signal was sinusoidal with an amplitude of 20 mV and a frequency of 1 kHz.
Additional Information
How to cite this article: Song, S. M. et al. Improved Drain Current Saturation and Voltage Gain in Graphene–on–Silicon Field Effect Transistors. Sci. Rep. 6, 25392; doi: 10.1038/srep25392 (2016).
Change history
27 June 2016
A correction has been published and is appended to both the HTML and PDF versions of this paper. The error has not been fixed in the paper.
References
Schwierz, F. Graphene transistors: status, prospects, and problems. Proceedings of the IEEE 101, 1567–1584 (2013).
Bolotin, K. I. et al. Ultrahigh electron mobility in suspended graphene. Solid State Communications 146, 351–355 (2008).
Schwierz, F. Graphene transistors. Nat Nanotechnol 5, 487–496 (2010).
Banerjee, S. K. et al. Graphene for CMOS and beyond CMOS applications. Proceedings of the IEEE 98, 2032–2046 (2010).
Novoselov, K. et al. A roadmap for graphene. Nature 490, 192–200 (2012).
Meric, I. et al. Channel length scaling in graphene field-effect transistors studied with pulsed current− voltage measurements. Nano letters 11, 1093–1097 (2011).
Meric, I., Baklitskaya, N., Kim, P. & Shepard, K. L. RF performance of top-gated, zero-bandgap graphene field-effect, Electron Devices Meeting (IEDM), 2008 IEEE International, San Francisco, CA, USA. doi: 10.1109/IEDM.2008.4796738 (2008, Dec. 15–17).
Wu, Y. et al. High-frequency, scaled graphene transistors on diamond-like carbon. Nature 472, 74–78 (2011).
Badmaev, A., Che, Y. C., Li, Z., Wang, C. & Zhou, C. W. Self-Aligned Fabrication of Graphene RF Transistors with T-Shaped Gate. Acs Nano 6, 3371–3376 (2012).
Pince, E. & Kocabas, C. Investigation of high frequency performance limit of graphene field effect transistors. Appl. Phys. Lett. 97, 173106 (2010).
Dimitrakopoulos, C. et al. Wafer-scale epitaxial graphene growth on the Si-face of hexagonal SiC (0001) for high frequency transistors. J Vac Sci Technol B 28, 985–992 (2010).
Lin, Y. M. et al. Operation of Graphene Transistors at Gigahertz Frequencies. Nano letters 9, 422–426 (2009).
Lin, Y. M. et al. 100-GHz Transistors from Wafer-Scale Epitaxial Graphene. Science 327, 662–662 (2010).
Liao, L. et al. High-speed graphene transistors with a self-aligned nanowire gate. Nature 467, 305–308 (2010).
Wu, Y. Q. et al. State-of-the-Art Graphene High-Frequency Electronics. Nano letters 12, 3062–3067 (2012).
Cheng, R. et al. High-frequency self-aligned graphene transistors with transferred gate stacks. P Natl Acad Sci USA 109, 11588–11592 (2012).
Feng, Z. H. et al. An ultra clean self-aligned process for high maximum oscillation frequency graphene transistors. Carbon 75, 249–254 (2014).
Meric, I. et al. Current saturation in zero-bandgap, top-gated graphene field-effect transistors. Nat Nanotechnol 3, 654–659 (2008).
Meric, I. et al. Graphene field-effect transistors based on boron–nitride dielectrics. Proceedings of the IEEE 101, 1609–1619 (2013),
Han, S.-J. et al. High-frequency graphene voltage amplifier. Nano letters 11, 3690–3693 (2011).
Han, S.-J., Reddy, D., Carpenter, G. D., Franklin, A. D. & Jenkins, K. A. Current saturation in submicrometer graphene transistors with thin gate dielectric: Experiment, simulation, and theory. ACS nano 6, 5220–5226 (2012).
Szafranek, B., Fiori, G., Schall, D., Neumaier, D. & Kurz, H. Current saturation and voltage gain in bilayer graphene field effect transistors. Nano letters 12, 1324–1328 (2012).
Meric, I. et al. Graphene field-effect transistors based on boron nitride gate dielectrics, Electron Devices Meeting (IEDM), 2010 IEEE International, 23.2.1–23.2.4, San Francisco, CA, USA. doi: 10.1109/IEDM.2010.5703419 (2010, Dec. 6–8).
Wu, Y. et al. Three-terminal graphene negative differential resistance devices. ACS nano 6, 2610–2616 (2012).
Adam, S., Hwang, E. H., Galitski, V. M. & Das Sarma, S. A self-consistent theory for graphene transport. P. Natl. Acad. Sci. USA 104, 18392–18397 (2007).
Li, X. M. et al. Graphene-On-Silicon Schottky Junction Solar Cells. Adv Mater 22, 2743 (2010).
Yang, H. et al. Graphene Barristor, a Triode Device with a Gate-Controlled Schottky Barrier. Science 336, 1140–1143 (2012).
Bartolomeo, A. D. Graphene Schottky diodes: An experimental review of the rectifying graphene/semiconductor heterojunction. Physics Reports 606, 1–58 (2015).
Kim, S. et al. Realization of a high mobility dual-gated graphene field-effect transistor with Al2O3 dielectric. Appl. Phys. Lett. 94, 062107 (2009).
Lafkioti, M. et al. Graphene on a hydrophobic substrate: doping reduction and hysteresis suppression under ambient conditions. Nano letters 10, 1149 (2010).
Deshpande, A., Bao, W., Milao, F., Lau, C. N. & LeRoy, B. J. Spatially resolved spectroscopy of monolayer graphene on SiO2 . Phys. Rev. B 79, 205411 (2009).
Dorgan, V. E., Bae, M.-H. & Pop, E. Mobility and Saturation Velocity in Graphene on SiO2 . Appl. Phys. Lett. 97, 082112 (2010).
Suryana, R., Nakatsuka, O. & Zaima, S. Formation of palladium silicide thin layers on Si(100) substrates. Jap. J. Appl. Phys. 50, 05EA09 (2011).
Wu, Y. et al. State-of-the-Art graphene high-frequency electronics. Nano Letters 12, 3062 (2012).
Fischetti, M. V., Neumayer, D. A. & Cartier, E. A. Effective electron mobility in Si inversion layers in metal–oxide–semiconductor systems with a high-κ insulator: The role of remote phonon scattering J. Appl. Phys. 90, 4587 (2001).
Acknowledgements
This work was supported by research grants from the National Research Foundation (NRF) of Korea (2010-0029132 and 2011-0031638).
Author information
Authors and Affiliations
Contributions
S.M.S. and B.J.C. designed the experiments; S.M.S. and B.J.H. performed the device fabrication and characterization. S.M.S., B.J.H., W.S.H. and B.J.C. analyzed the data and wrote the manuscript. All authors discussed the results and commented on the manuscript.
Corresponding author
Ethics declarations
Competing interests
The authors declare no competing financial interests.
Supplementary information
Rights and permissions
This work is licensed under a Creative Commons Attribution 4.0 International License. The images or other third party material in this article are included in the article’s Creative Commons license, unless indicated otherwise in the credit line; if the material is not included under the Creative Commons license, users will need to obtain permission from the license holder to reproduce the material. To view a copy of this license, visit http://creativecommons.org/licenses/by/4.0/
About this article
Cite this article
Song, S., Bong, J., Hwang, W. et al. Improved Drain Current Saturation and Voltage Gain in Graphene–on–Silicon Field Effect Transistors. Sci Rep 6, 25392 (2016). https://doi.org/10.1038/srep25392
Received:
Accepted:
Published:
DOI: https://doi.org/10.1038/srep25392
This article is cited by
-
A novel design of graphene field-effect transistor-based out-phasing power amplifier
Journal of Computational Electronics (2023)
-
High-Gain Graphene Transistors with a Thin AlOx Top-Gate Oxide
Scientific Reports (2017)
Comments
By submitting a comment you agree to abide by our Terms and Community Guidelines. If you find something abusive or that does not comply with our terms or guidelines please flag it as inappropriate.